Full Metal Inductive Sensors for The Food Industry

Neat and clean.
  • Increased sensing ranges and correction factor 1 for steel and stainless steel.
  • Wide temperature range of 0...100 °C.
  • Temperature shock resistant even in case of frequent temperature fluctuations.
  • High ingress protection: IP 67 / IP 68 / IP 69K; food-grade housing materials.
  • Resistant to high-pressure cleaning and aggressive cleaning agents.
Increased sensing ranges
The increased sensing ranges for non-flush installation give you more safety in case of mechanical tolerances.

Ingress protection in hygienic and wet areas
The sensors for use up to 100 °C undergo frequent cleaning operations, temperature shocks and feature high resistance to cleaning agents.

Application tests
A series of tests qualified the sensors for food applications:
  • temperature shock test to EN 60068-2-14 Nc
  • artificial ageing in a 1000-hour long-term test to EN 60068-2-14 Nb (change of temperature)
  • leak check using the steam boiler test
Applications:
hygienic and wet areas in the food industry.

M12 connector · output function NO · 3-wire DC PNP
IFT245 - Type M12, length 70 mm, sensing range 6 mm nf, frequency 500 Hz
IGT249 - Type M18, length 70 mm, sensing range 12 mm nf, frequency 500 Hz
IIT231 - Type M30, length 70 mm, sensing range 25 mm nf, frequency 250 Hz

M12 connector · output function NO · 3-wire DC NPN
IFT246 - Type M12, length 70 mm, sensing range 6 mm nf, frequency 500 Hz
IGT250 - Type M18, length 70 mm, sensing range 12 mm nf, frequency 500 Hz
IIT232 - Type M30, length 70 mm, sensing range 25 mm nf, frequency 250 Hz

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more